Skip to content

Tutorials

Getting started with LuthierXpert

Short videos, one per task, with the steps written underneath. Follow them in order for your first guitar, or jump straight to the tool you need.

1 The design brief

Every dimension of your guitar in one place: scale, playability, neck, body, bridge, pickups. The solver checks everything live.

Set the guitar dimensions · 1 min 20

  1. In the left-hand menu, open Design brief.
  2. By default, the essentials are shown: fundamentals, pickups, electronics.
  3. Tick Expert, top right of the panel, to see every dimension: playability, nut, headstock, fretboard, neck, heel, body, bridge, pickups.
  4. Pick a bridge from the Bridge list: its details fill in under Bridge (detail).
  5. Click a section title to open or close it.
  6. Click a value and type your own, or use the small arrows next to it: the guitar updates.
  7. Keep an eye on the bottom bar: the solver recalculates the neck angle and the bridge margin live.

2 Edit a shape in 2D

The outline of the body, headstock and neck: move, add and adjust, while keeping the guitar accurate and playable.

Edit the body outline · 48 s

  1. In the left-hand menu, open 2D › Body.
  2. Grab a control point and drag it: the outline follows.
  3. Zoom in on the area you are reshaping to place the point precisely.
  4. Fine adjustment with the keyboard: arrows 0.5 mm, Shift 0.1 mm, Ctrl 5 mm.
  5. Right-click: add a point · double-click: delete it · H: smooth or sharp point · Ctrl+Z / Ctrl+Y: undo / redo.
  6. Check bottom left that the solver stays COHERENT, then go back to 2D › Assembly.

Redraw a guitar from a drawing: the ghost · 2 min 40

  1. In 2D › Assembly, open the reference Ghost panel on the right.
  2. Load a file: a drawing or a photo in DXF, PDF, PNG, JPEG or WebP. It shows through under the guitar.
  3. Turn on Position mode: drag to move the ghost, use the handles for scale and rotation, the wheel to zoom (Shift fine, Ctrl fast).
  4. Alignment: 90° rotations and mirrors to put the drawing the right way round. Set the opacity of the ghost and of the guitar to see both.
  5. Turn position mode off, then open Body and Neck: the ghost aligned in Assembly follows there. Move the outline points to follow the drawing.
  6. One click on Visible hides or shows the ghost to compare. Save the project; Clear the layer removes the ghost.

3 Sculpt in 3D, tool by tool

Each sculpting tool, one at a time: what it does and how to set it.

Bevel and edge fillet · 2 min

  1. Open 3D in the left-hand menu. Drag to orbit, right-drag to pan, wheel to zoom.
  2. Choose the face to work on: Top or Back. The active face is drawn in full colour.
  3. Bevel: pick Bevel, click Set a bevel, place points A and B on the edge, set the Depth, then Apply.
  4. Edge fillet: pick Edge fillet, choose Round or Chamfer, set the Radius, then All around. Exclude A→B keeps a portion sharp.
  5. Do the same on the other face.
  6. On this face lists the cuts in workshop order (carve, bevel, edge fillet): ✕ removes one, Remove all starts from scratch.

Custom chamfer · 1 min 50

  1. In 3D, choose the face (here Back) and the Bevel tool. The Custom chamfer section is under the bevel cut.
  2. Click Add chamfer (top) or Add chamfer (bottom): a cut line with three points appears on the edge. All around follows the whole outline.
  3. Drag the points and their tangent handles to draw the cut boundary on the face. Double-click adds or removes a point; Ctrl + double-click pinches it.
  4. Set Depth (all points). Hollow goes from a flat cut to a hollow one.
  5. Click Apply the chamfer, then turn the guitar to check the result.

The volute · 1 min 20

  1. In 3D, choose the Back face and the Volute tool.
  2. Keep Symmetric (or pick Free), then click Place the volute: four curves appear on the neck — the crest (yellow), its twin lower on the edge (red), the U on the round of the shaft (blue).
  3. Zoom in and drag the points and their handles. Arrows move a point by 0.5 mm (Shift 0.1, Ctrl 5); Tab switches between point and handles; H pinches.
  4. Set Crest relief (the height of the volute) and Landing (behind the crest).
  5. Click Apply the volute.

4 Finishes

Woods, colours, lacquer and hardware, then the 360° video of your guitar.

Woods, colours, hardware and 360° video · 1 min 55

  1. Open Finishes in the left menu: the Design panel shows the finished instrument, as it will leave the workshop. Your choices are saved with the model.
  2. Wood: pick the species of each part (body, neck, headstock veneer, fretboard) and set its Grain. The volume and weight of each part are shown, with the estimated mass of the instrument.
  3. Tints: click a colour for the body and headstock face, or + to create your own.
  4. Headstock: Matched to the body, Own tint or Natural wood.
  5. Sunburst: a gradient from the centre to the edge of the top. Set Body width and Headstock width, or choose No sunburst.
  6. Hardware: Chrome, Gold, Black or Carbon. Ambience: Atelier, Vitrine or Scene, and the Gloss, from oiled to mirror.
  7. Share › 360° video: your guitar on video, ready for social media.

5 Exports

Full-scale paper plans, DXF, STL and STEP: what to export, and what for.

Paper plans, DXF, STL and STEP · 1 min 15

  1. Open Export in the left menu: what leaves the workshop, the paper plan and the files for external CAD or CAM.
  2. 1 · Paper plan: a dimensioned plan at 1:1, ready to stick on the part. Pick Assembled, Body, Neck or Fretboard.
  3. Or a 1:1 shop template instead of a part: Tuner drilling, Complete body (layout) or Bevels / free chamfers.
  4. Choose A0 — single sheet or A4 — tiled, then Save as PDF or Print….
  5. 2 · Files for CAD / CAM: pick the part (Body, Neck, Fretboard or All), then 2D — outlines for a DXF, or 3D — solids for an STL or a STEP. Millimetres, 1:1.
  6. The files are computed on the LuthierXpert server in a few seconds. An STL has no unit: when you import it (in Fusion: Insert Mesh), choose Millimeter.

6 Machining

Stock, cutters, G-code and flipping the part: from the screen to the machine.

From the body to G-code, in four tabs · 1 min 50

  1. Open CNC machining. Tab 1 · Part and face: pick the part (body, neck or fretboard), then the face: the top first, the back afterwards if it has pockets.
  2. Tab 2 · Blank and zero: LX measures the part and proposes a board with margin. Only change its size if your board is different.
  3. Place the part in the board (rotation, offsets, or with the mouse), check which way the axes go and the zero, then choose the tabs that hold the part during the cut-out.
  4. Tab 3 · Cutters: one cutter per operation, with its passes: stepover, step-down, stock allowance, feeds and spindle speed.
  5. Tab 4 · Program: roughing, finishing, ball finishing, flip locating pins if the back is machined, and contour cut-out. Click Compute and view: the G-code is computed on the LuthierXpert server, then the toolpath is shown in 3D.
  6. Click Save files and choose your folder: the G-code files are ready for the machine.

Add your own cutters · 45 s

  1. In CNC machining, tab 3 · Cutters, click Manage cutters… under the list of operations: the catalogue opens.
  2. Click New cutter… at the bottom of the list, or select a similar cutter and click Duplicate.
  3. Choose the Type (flat, ball, bull-nose, slotting), then enter diameter, usable length, shank diameter, number of flutes, feeds and spindle speed. The name fills in by itself from the geometry.
  4. LX warns you when a value looks wrong, for instance a shank thinner than the cutting diameter.
  5. Click Save cutter, then Close.
  6. Pick the new cutter in an operation’s list: its passes are recalculated from its diameter. Use Export / Import a library… to bring it to another computer.

A question not covered here? Support →